At a speciﬁc load of 453 tdm² and 178 Nm³kg cooling air a cold clinker temperature of 65˚C above ambient temperature is achieved The intensive cooling of the clinker is realised by a long retention time inside the cooler At maximum stroke numbers of 4 min1 the ETA cooler can be operated with clinker bed heights of up to 1300 mm... As a leading global manufacturer of crushing equipment, milling equipment,dressing equipment,drying equipment and briquette equipment etc. we offer advanced, rational solutions for any size-reduction requirements, including quarry, aggregate, grinding production and complete plant plan.Get Price
Limestone is mainly composed of calcium carbonate (CaCO3), MO's Hardness 3 degrees. The limestone particles or powders can be used in building materials, road construction, metallurgy, chemical and other industries after crushing or grinding.
Main Equipments: jaw crusher, cone crusher, ball mill, flotation cell, thickner and bucket hoist conveyor.
Granite Crushing production line in Cameroon is composed of GZD1300 × 4900 vibrating feeder, PE900 × 1200 jaw crusher, FTMCS430 single-cylinder hydraulic cone crusher, PF1315 impact crusher, 2YK2460 circular vibrating screen, 2YK2160 circular vibrating sc
The whole equipment includes vibrating feeder, jaw crusher, Raymond mill, bucket elevator, belt conveyor, adjusting hopper, control cabinet, etc. The main grinding equipment is our patented product, 4525 Raymond Mill, with the capacity of 35t/h.
Application Area:Building materials, chemicals, fertilizer, metallurgy, mining, refractory, ceramic, steel, thermal power, coal, etc.
Gypsum powder plant is a kind of micronized line which turns natural dihydrate gypsum ore (raw gypsum) or industrial by-product gypsum (desulphurization gypsum, phosphogypsum, etc.) into construction gypsum (calcined gypsum) through crushing, grinding, he
The results obtained from XRD petrographic analysis and SEM qualitatively show that when the calcination temperature or cooling rate is improved or the holding time is prolonged appropriately the C 3 S content in HMLHC clinker increases while the C 2 S content decreases and the generation and growth of periclase crystals are promoted Improving the calcination temperature the later after 28
Cooling Air Quantity is maintained to ensure cooling of clinker and heat recuperation from hot clinker from kiln Specific air usage is generally considered as key performance indicator of cooler New generation coolers can cool clinker to the temperatures to as low as 65 0C over ambient with a specific air consumption of 17 kgkgclinker
Using the COTDMA algorithm this article obtains the unsteady state change progress of the air temperature and the clinker and the influence of the porosity size on the cooling process providing
Clinker cooling By Arthur Harrisson Published 16 March 2015 after the burning zone and up until the clinker’s eventual delivery to the cement mill can also have a significant effect on the quality of cement produced including the secondary air temperature and the closeness of the burning zone to the outlet As the temperature
The temperature of clinker melt occurrence varied slightly depending first on the type of raw meal used 227 Clinker cooling 13 228 Cement Blending and Grinding 14 23 PhysioChemical Process of Portland Cement Clinker Formation 14 231 Clinker Phases 14 a Alite C 3
The air entering the final cooling compartment l 24 which is also heated in passing through the clinker on the rear or discharge end portion of the grate 2 but to a lesser ldegree than the air entering the precooling chamber 23 since the temperature of the clinker has been reduced in passing through the precooling compartment 23 passes into
Reciprocating movement of cooler results in an immediate uniform distribution and a true continuous flow of clinker over the grate A thin even bed approximately 4in in depth results in a better distribution of air through the clinker Final temperature of minus 1 in clinker is approximately 100° F above that of the cooling air
Jan 01 2015 · The effects of mass flow rate and temperature of cooling air on the performance of the GCC and RK are investigated It is found that the first and secondlaw efficiencies of the RK can be increased by 262 and 213 respectively by increasing the mass flow rate of cooling air
The purpose of the present study is to develop a simplified dynamical model of clinker cooling process performed in grate coolers The responses of three different pressures to changes of the
cooling rate of the clinker The highest temperature form α can contain several percent of Al 2 O 3 Fe 2 O 3 and alkali However the lower temperature forms α’ and β can only hold a small amount •On cooling and phase change therefore the impurities are exsolved and cause a clouding of the crystals
May 23 2019 · The Coanda Wing plates allow air to pass but not clinker Fines are swept to the clinker bed surface and the Coanda Wing plates are completely surrounded by cooling air During normal operation temperatures of between 30° C and 40° C are measured close to the grate surface
The clinker on the grate plate will be rapidly cooled by the highpressure cooling air blowing from the fan below and with the grate plate pushing forward constantly exchange heat with the cold air until reaching the qualified discharge temperature After cooling the small particle clinker will fall through the grate seam and grate hole so
Jun 14 2011 · So does r and Potassium have the strongest effects followed by Sodium andMagnesium Therefore MgO SO3 and K2O to a certain concentration aregood coating unately the liquid properties that induce C3S formation aredetrimental to the refractory lining and to clinker nodulization
Variations in cooling rate of the clinker in the kiln and subsequent changes in the proportions or size of the C 3 A crystals may also have an effect on setting characteristics If the rate at which sulfate is supplied by the different sulfate salts exceeds the rate at which the clinker minerals principally the aluminate phase can react the
The temperature distribution uniformity and the magnitude of the temperature gradients in the quenched solid have a primary effect on distortions and residual stresses On the path to determine the effect of the cooling gas ﬂow on these undesirable phenomena it is thus easier and rather useful to ﬁrst ﬁnd the sensitivity of these
Dec 11 2018 · It is normally caused by cooling of the clinker by the secondary air as it falls over the nose ring at There should be no effect on kiln bricks The clinker mineral composition will be changed with that secondary air temperature remains approx 100150 deg low There is change in plate design
A cooling grate for cooling and transporting of cement clinker having at least one grate element with at least one support for cement clinker having at least one cooling air channel discharging into the support which is inclined in conveying direction at least in a section adjacent to its outlet used to inject cooling air into the clinker has improved cooling characteristics if the cooling
The hot clinker discharged from the kiln at a temperature of about 1300 C is further treated in clinker cooler The cooling of clinker influences its structure main composition grindability and consequently the quality of the resulting cement
effect of cooling rate on the composition and crystal structures crystallization of alite and belite of clinker 59 Generally there are four types of clinker cooler Rotary
Feb 21 2013 · This causes an especially largearea injection of cooling air into the clinker bed located on top of the support As a result the cooling air temperature above the clinker bed is increased and the risk of the formation of air tunnels is decreased Furthermore the required fan power for an adjusted amount of cooling air is decreased
Forcedair cooling is advantageous in a number of different scenarios For example forcedair cooling of electronic components in an industrial setting is significantly more efficient than convection cooling as it reduces air temperature in the general vicinity of the components being cooled and improves the heat transfer coefficient
Clinker is a nodular material produced in the kilning stage during the production of cement and is used as the binder in many cement products The lumps or nodules of clinker are usually of diameter 325 mm and dark grey in color It is produced by heating limestone and clay to the point of liquefaction at about 1400°C1500°C in the rotary kiln